Quick answer: A used Kubota tractor in the 70 hp class is the right size for farms of roughly 20 to 60 hectares. The Kubota M7040 we stock measures 4,110 x 1,950 x 2,530 mm, weighs 2,400 kg, and runs a four-cylinder V3800-DI-T turbo diesel rated at 72 hp at 2,500 rpm with 45.6 kW available at the PTO. Buyers choose it for three practical reasons: the 1,950 mm width clears orchard rows and narrow village roads, the Category II hitch still handles a two-furrow reversible plough or a 1.8-2.0 m rotary tiller, and two units load into one 40HQ container with nothing dismantled. Check the PTO speed on the nameplate before you match implements.

Linyi Gama Machinery Co., Ltd +86 13013532997

Why 70 HP Is the Sweet Spot for 20-60 Hectare Farms

Sizing a used Kubota tractor this way avoids the two common buying errors. Below 60 hp, the machine runs out of PTO power in a 2.0 m tiller and struggles with a loaded trailer on a slope. Above 90 hp, you pay for mass you may not need: the 100 hp tractors we ship weigh close to 3,900 kg, while the M7040 works at 2,400 kg. That is about 33 kg per horsepower against roughly 39 kg on a 100 hp unit, and the difference shows up as less compaction in paddy soils and in soft ground after rain. The trade-off: a lighter tractor needs front ballast when you hang a heavy implement on the Category II hitch.

Fuel capacity is 85 litres, enough for a full working day in most tillage jobs. Ground clearance of 490 mm at the front axle and a 4.2 m turning radius let the machine cross bunds and turn at the headland without a three-pass shuffle. That balance is what keeps a used Kubota tractor productive in both dryland and paddy work.

Used Kubota Tractor Specs That Matter in the Field

The table below lists the figures that decide whether the machine fits your implements and your container, not the marketing numbers.

Two numbers deserve attention when you compare a used Kubota tractor against a Chinese 70 hp model. First, the 12.9 kN lift figure is measured 610 mm behind the link ends, not at the ball; ask any supplier which standard they quote, because the same hitch looks about 30% stronger on paper at the link end. Second, the PTO: 540/720 rpm is standard on this platform, while most European implements expect 540/1000. A 720 rpm shaft will not drive a 1,000 rpm baler, so confirm the shaft and the nameplate in writing before the pro-forma invoice is signed.

Implement Matching: What a 12.9 kN Hitch Really Lifts

At 12.9 kN, or roughly 1,316 kg, the M7040 is comfortable with a two-furrow reversible plough, a 1.8-2.0 m rotary tiller, a light 14-16 disc harrow, a 1.2-1.4 m flail mower, and a mounted unit such as our 1LY disc plough, which needs 60 hp and a Category II hitch. It is not comfortable with a three-furrow plough in heavy clay. No front loader is fitted unless you specify it, so order the loader brackets with the machine rather than after it lands.

+86 13013532997 Gavin@gamagr.com

Container Math and Pre-Shipment Checks for a Used Kubota Tractor

Freight is where importers lose money. A 40HQ container measures about 12,032 mm long, 2,352 mm wide and 2,690 mm high inside, with a door opening near 2,580 mm. The M7040 at 2,530 mm high and 1,950 mm wide goes in whole: no exhaust removal, no mirror removal, no frame folding. Two units nose-to-tail use 8,220 mm, leaving roughly 3,800 mm for a disc plough, a spare tyre set and service parts in the same box. For a used Kubota tractor, landed freight per unit drops sharply when two machines share one box. A 20GP is a different case; its door opening is around 2,280 mm, so the safety frame has to come down and the machine arrives needing reassembly.

These six checks take about two hours per used Kubota tractor and cost far less than a claim after arrival. Run the list before the truck leaves the yard. One, compare the hour meter reading with an oil sample and with tyre wear. Two, test PTO clutch engagement under load, not on the stand. Three, check 4WD engagement and the rear differential lock. Four, run a 30-minute hydraulic drop test with a loaded implement; more than 20 mm of sink points to worn lift seals. Five, inspect sidewall cracking on the 9.5-24 front tyres. Six, look for coolant weep and oil mist around the V3800 turbo.

FAQ

Is 70 hp enough for a 60-hectare farm?

Yes for arable work with a 2.0 m tiller or a two-furrow plough, because the 45.6 kW at the PTO is what actually drives the implement. If your ground is heavy clay, or you need three furrows in one pass, move up to the 90-100 hp range and accept the extra weight and freight.

GAMA Machinery company

How many used Kubota tractors fit in a 40HQ container?

Two, loaded nose-to-tail, with room left over for implements and spare parts. The 2,530 mm height and 1,950 mm width clear the door opening, so nothing has to be dismantled. That is why dealers prefer 70 hp machines to 100 hp units that arrive with the cab or exhaust removed.

Sourcing a Used Kubota Tractor From Linyi, China

Linyi Gama Machinery Co., Ltd, based in Linyi City, Shandong Province, China, keeps Japanese and Chinese used tractors in stock across the 50-110 hp range, including the 70HP M7040 Kubota used tractor and the 70HP M704KQ Kubota used tractor with cabin. Every used Kubota tractor we ship is inspected against the six-point list above, photographed, and loaded with the PTO speed confirmed on the nameplate. Send your horsepower range, implement list and destination port to Gavin@gamagr.com or call +86 13013532997 (WeChat / WhatsApp) for the current stock list and a landed-cost quotation.